|
|
| |
Aisle 1: LED Replacements
for Incandescent Bulbs
View Your Cart / Checkout
View Your Cart / Checkout
LED Lamps Replace Hot Incandescent and Halogen Bulbs Used for RV and Boat Interior Lighting Fixtures. You save 80% in power and run cooler.
We are proud to say that all bulb replacement offered here are 
by
LightBlasters™
in Mesa, AZ using next-generation Hybright
LEDs.
nexLED™
LED Lamps are designed to replace the most common types of 12-volt DC incandescent and halogen bulbs in RVs and Boats:
G4 Halogen series
15mm Bayonet series
921 Wedge series
LightBlaster bulb replacements are LED lamps that plug directly into the most common 12-volt DC incandescent bulb fixtures. You do not have to replace the fixture, it is the same as before.
LightBlaster bulb replacements feature solid state construction designed to last as long as the LEDs, circuitry to allow operation in the variety of electrical environments and power conditions found in RVs and Boats, and solid copper heat sinks to protect the LEDs and ensure their extended lifetime of 11 years.
These LED products are correctly called "lamps" and not "bulbs" because there is no need for a protective glass bulb to cover and protect the filament, but you can call them LED Bulbs is you wish.
They feature solid state construction designed to last as long as the LEDs, circuitry to allow operation in the variety of electrical environments and power sources found in RVs and Boats, and heat sinks to protect the LEDs and ensure their extended lifetime of 11 years of continuous usage.
NOTE:
nexLED™
technology is USA Patent Pending
NOTE:
zipLED™
connectivity is USA Patent Pending
fLEDescent™
is a trademark of PrudentRVer.com
NOTE: One HyBright.3 LED chip emits 20 lumens of white light at 12.5 to 13.8 volts. The Starion LED chip emits 110 lumens in a power-regulated environment.
Wrong Aisle? Try
Aisle 2: LED Replacements for Fluorescent Fixtures
|
|
Go to Top
--
View Your Cart / Checkout
LED Replacements for
G4 Halogen Bulbs
Halogen lighting is used extensively in some of the newer high-end motorcoaches and some trailers. The fixture most commonly used is the "puck" fixture, named for its similar shape to that of a hockey puck. The fixture is recessed into the ceiling or underside of the cabinetry over working surfaces.
The halogen bulb used in a puck fixture is typically a 12-volt 10-watt bulb with a 4 mm spacing on the bi-pin mounting. It slides at a slight angle to horizontal into a G4 ceramic socket surrounded by a faceted mirror reflector.
Halogen lighting is used extensively in some of the newer high-end motorcoaches and some trailers. The fixture most commonly used is the "puck" fixture, named for its similar shape to that of a hockey puck. The fixture is recessed into the ceiling or underside of the cabinetry over working surfaces.
The halogen bulb used in a puck fixture is typically a 12-volt 10-watt bulb with a 4 mm spacing on the bi-pin mounting. It slides at a slight angle to horizontal into a G4 ceramic socket surrounded by a faceted mirror reflector.
Halogen lighting is used extensively in some of the newer high-end motorcoaches and some trailers. The fixture most commonly used is the "puck" fixture, named for its similar shape to that of a hockey puck. The fixture is recessed into the ceiling or underside of the cabinetry over working surfaces.
The halogen bulb used in a puck fixture is typically a 12-volt 10-watt bulb with a 4 mm spacing on the bi-pin mounting. It slides at a slight angle to horizontal into a G4 ceramic socket surrounded by a faceted mirror reflector.
|
The JC12v10w halogen bulb is used in a
puck-shaped task-light fixture that fits into the ceiling or
the underside of cabinets to illuminate counters and desktops.
It may also be used in other halogen fixtures in both a
horizontal and a vertical orientation. Click on the image for
bulb specifications.
|
Most
puck fixtures are rated for 12v-10W bulbs. That means the
fixture becomes a significant fire danger if operated with a larger
wattage bulb. You have to remove the fixture to see this rating on
the backside of the fixture.
However, in parts stores you can purchase 15w,
20w, and even up to 50w bulbs that look identical, and some people
replace their halogen bulbs with the larger wattage bulb. Using a
higher wattage halogen bulb can significantly increase the danger of
damage and fire. Leaving the front cover or glass lens off the
fixture in hopes that the increased ventilation will compensate is
not recommended. The danger is still there.
DO NOT
EXCEED the rated wattage of your halogen fixture. Use more
LEDs if you want more light .
.
.
|
Add to Cart
ships
from
stock |
G4.RV2N-H : a CR90 warm white
nexLED™ HyBright.3 LED lamp
specifically designed for use in the halogen "puck" fixture
found in the ceilings and over the counters of many high-end
motor coaches and other RVs. These LEDs are the latest
development in the HyBright technology and provide good
excellent color rendering at 3800K color temperature.
6 HyBright.3 LED
chips on a flat board
18 LEDs, WW (3800K)
Bi-Pin base for G4 socket
120 lumens
wide-angle
perpendicular
to the board
12.5 volts nominal
11
to 18 volt operating range
Power-limiting circuit protects LEDs
0.14 amps nominal
1.75 watts
100,000 hour lifetime
This
lamp replaces the typical 12v10w halogen bulb found in most
"puck" fixtures in high-end motorcoaches and trailers. The
lamp's 120 lumens is about the same as seen in the
halogen fixtures since none of its luminosity is lost to the
reflector.
This lamp is a great replacement in most
puck fixture applications, especially where there is danger
from the heat produced by the halogen bulbs. However, some
brands of fixture have placed the socket very close to the
lens, and do not leave sufficient room for the LED
lamp.
The CR90 color rendering of the LEDs is
in the warm range, and applications requiring accurate color
rendering, such as oil painting are well served.
|
Add
to Cart
ships
from
stock |
G4.RV3N-Flex : a 200 lumen CR90
warm white nexLED™ HyBright.3 LED lamp
specifically designed for use in halogen fixtures with
horizontal or vertical sockets. A lens cover is required to
hold the disk in place.
The G4.RV3N-Flex and be used in the
halogen "puck" fixture found in the ceilings and over the
counters of many high-end motor coaches and other RVs.
These LEDs are
the latest development in the HyBright technology and provide
good excellent color rendering at 3800K color
temperature.
10 HyBright.3 LED
chips on a flat board
30 LEDs, WW, CR90
Bi-Pin base for G4 socket on flexible
wire
200 lumens
wide-angle
perpendicular
to the board
12.5 volts nominal
11
to 18 volt operating range
Power-limiting circuit protects LEDs
0.14 amps nominal
2.9 watts
100,000 hour lifetime
This lamp replaces a 12v10w or 12v20w
halogen bulb that may be found in "puck" fixtures in
high-end motorcoaches and trailers. The lamp's 200 lumens
is brighter than seen in the halogen fixtures since none
of its luminosity is lost to the reflector.
This lamp is a great replacement in many
halogen applications, especially where there is danger from
the heat produced by the halogen bulbs. However, a lens
or some other means for holding the LED disc in place is
required.
The CR90 color rendering of the LEDs is
in the warm range, and applications requiring accurate color
rendering, such as oil painting are well served.
|
SOLD OUT
use
G4.RV2N-H
G4.RV3N-Flex |
G4.RV2-H : a natural white
nexLED™ HyBright.3 LED lamp
specifically designed for use in the halogen "puck" fixture
found in the ceilings and over the counters of many high-end
motor coaches and other RVs. These LEDs are the latest
development in the HyBright technology and provide good color
rendering at 5200K to 5500K color temperature.
6 HyBright.3 LED
chips on a flat board
18 LEDs, CW
Bi-Pin base for G4 socket
120 lumens
wide-angle
perpendicular
to the board
12.5 volts nominal
11
to 18 volt operating range
Power-limiting circuit protects LEDs
0.14 amps nominal
1.75 watts
100,000 hour lifetime
This lamp replaces the typical JC12v10w
halogen bulb found in most "puck" fixtures in high-end
motorcoaches and trailers. The lamp's 120 lumens is about
the same as seen in the halogen fixtures since none of its
luminosity is lost to the reflector.
This lamp is a great replacement in most
puck fixture applications, especially where there is danger
from the heat produced by the halogen bulbs. However, some
brands of fixture have placed the socket very close to the
lens, and do not leave sufficient room for the LED
lamp.
The color rendering of the LEDs is in the
cool to warm range, so applications requiring accurate color
rendering, such as oil painting, may require use of more
sunlight-like lighting.
|
|
Add to Cart
ships
from
stock |
G4.RV2-VV : a natural white
nexLED™ HyBright.3 LED lamp
specifically designed for use in the
halogen "tulip" spotlamp fixture found in the
ceilings and over the counters of many high-end motor coaches
and other RVs. (See a closeup of the photo to the left --
fixture is not provided.) These LEDs are the latest
development in the HyBright technology and provide good color
rendering in the 5200K to 5500K color temperature
range.
6 HyBright.3 LED
chips on a flat board
18 LEDs, CW
Bi-Pin base for G4 socket
120 lumens
wide-angle
perpendicular
to the board
12.5 volts nominal
11
to 18 volt operating range
Power-limiting circuit protects LEDs
0.14 amps nominal
1.75 watts
100,000 hour lifetime
This lamp replaces the typical JC12v10w
halogen bulb found in vertical halogen fixtures in
high-end motorcoaches and trailers. The lamp's 120 lumens
is about the same as seen in the halogen fixtures since
none of its luminosity is lost to the reflector.
This lamp is a great replacement in most
vertical fixture applications, especially where there is
danger from the heat produced by the halogen bulbs.
The color rendering of the
LEDs is in the cool to warm range, so applications requiring
accurate color rendering, such as oil painting, may require
use of more sunlight-like lighting.
|
Add to Cart
ships
from
stock |
G4.RV3-H : a white nexLED™ HyBright.3 LED lamp
specifically designed for use in the halogen "puck" fixture
found in the ceilings and over the counters of many high-end
motor coaches and other RVs.
9 HyBright.3 LED
chips on a flat board
3 rows of
3 chips each
27 LEDs, CW
Bi-Pin base for G4 socket
180 lumens
wide-angle
perpendicular
to the board
12.5 volts nominal
11 to
13.8 volt operating range
0.21 amps
nominal
2.63 watts
100,000 hour lifetime
Color options:
cool
warm This lamp replaces the
typical JC12v10w or JC12v20W halogen bulb found in most "puck"
fixtures in high-end motorcoaches and trailers. The lamp's 180
lumens remains brighter than the typical 140 lumens (that
drops with age) of the halogen fixtures, and none of its
luminosity is lost to the reflector.
cool
warm This lamp replaces the
typical JC12v10w or JC12v20W halogen bulb found in most "puck"
fixtures in high-end motorcoaches and trailers. The lamp's 180
lumens remains brighter than the typical 140 lumens (that
drops with age) of the halogen fixtures, and none of its
luminosity is lost to the reflector.
This lamp is a great replacement in most
puck fixture applications, especially where there is danger
from the heat produced by the halogen bulbs. However, some
brands of fixture have placed the socket very close to the
lens, and do not leave sufficient room for the LED
lamp.
The color rendering of the LEDs is in the
cool to warm range, so applications requiring accurate color
rendering, such as oil painting, may require use of more
sunlight-like lighting.
| |
Go to Top -- View Your Cart / Checkout
15mm Bayonet Series Bulbs
If your incandescent bulb looks like one of
those below, you have a bulb with a 15 millimeter diameter metal
base. There will be two small "ears" on opposite sides of the can
near the bottom of the bulb that are used to latch into the bayonet
socket of the light fixture. On the bottom will be one or
two electrical contact points.
LightBlasters does not support the B9 base at
this time.
Replacements
|
The BA15s type bulbs come
with a grounded 15mm diameter bayonet base, symmetric ears,
and a single contact for the positive connection. Typical bulb
numbers are 67, 93, 1003, 1073, 1141, 1143, 1156, 1295, and
1651. |
Replacements
|
Two BA15s type bulbs are
used specifically for spotlight and reading lamp applications.
They are the 1139 and 1383 shown in the photos. |
Replacements
|
The BA15d type bulbs come
with an electrically neutral 15mm diameter bayonet base,
symmetric ears, and two contacts for the positive and
ground connections. Typical bulb numbers are 68, 90, 94, 1004,
1076, and 1142. |
We have no replacements
|
The BAY15d type bulbs come with a
grounded 15mm diameter bayonet base, assymmetric ears to
define polarity, and two contacts for two positive
voltage-level connections. Typical bulb numbers are 1016,
1034, 1154, 1157, and 1176. These bulbs are typically used for
dual function automotive lights, and LightBlasters does not
provide replacements for this kind of bulb.
|
LED
Replacements for
15mm Bayonet Single Contact (BA15s) Bulbs
|
<>
|
ZLS w/base and metal cookie
for
Add to Cart
ships
from
stock |
B15s.ZLS : the brightest nexLED™
lamp made to date provides 220 lumens from a single LED
LightStick with two white Starion LED chips and a power
regulation circuit. Plugged into a B15s.ZLX base, one ZLS
provides 3.5 times the brightness of a ZL3,
exceeding the brilliance of an 1156 bulb.
2
each Starion(tm) LED chips
on a flat pcb
0.5 by
1.5 inches printed circuit board
double-stick
thermal tape backing
18 LEDs
per chip, 36 total
220 lumens,
natural white color
wide-angle
perpendicular
to the board
Color Rendering Index
of 92
Color Temperature of
3500 ~ 4500K
Power regulation
controls internal voltage
12.5 volts nominal internal voltage
10
to 30 volt operating range
2.4
watts, 0.2 amps at 12v
0.1 amps at 24v
Use with
pulse-width-modulation dimmers
Variable
voltage dimmers don't work
Operating
temperature 130F
LightStick
must be thermally attached to
12 sq-in of metal for proper operation
Will not melt
plastic lens cover
B15s.ZLX
socket
BA15s
base
(bayonet, 15mm)
10 mil aluminum
mounting plate (cookie)
3.4 x 3.4
inches, routing holes for wiring
100,000 hour lifetime
The
double-stick tape on the back of the LightStick, and the
mounting plate (cookie), allows the B15s.ZLS to be arranged in a
variety of ways. The cookie can be trimmed to fit the
fixture. LightSticks can also be mounted to the back of
the light fixture if the metal area is sufficient to act as a
heat sink (12 square inches minimum).
Three ZLS LightSticks,  using 7.2 watts, can be mounted
in a Surface Mount RV Scare Light to exceed the light output
of the standard 37.5 watt 1295 bulb. Use up to six
ZLSs for even more light. Purchase additional ZLSs LightSticks
here.
2
each Starion(tm) LED chips
on a flat pcb
0.5 by
1.5 inches printed circuit board
double-stick
thermal tape backing
18 LEDs
per chip, 36 total
220 lumens,
natural white color
wide-angle
perpendicular
to the board
Color Rendering Index
of 92
Color Temperature of
3500 ~ 4500K
Power regulation
controls internal voltage
12.5 volts nominal internal voltage
10
to 30 volt operating range
2.4
watts, 0.2 amps at 12v
0.1 amps at 24v
Use with
pulse-width-modulation dimmers
Variable
voltage dimmers don't work
Operating
temperature 130F
LightStick
must be thermally attached to
12 sq-in of metal for proper operation
Will not melt
plastic lens cover
B15s.ZLX
socket
BA15s
base
(bayonet, 15mm)
10 mil aluminum
mounting plate (cookie)
3.4 x 3.4
inches, routing holes for wiring
100,000 hour lifetime
The
double-stick tape on the back of the LightStick, and the
mounting plate (cookie), allows the B15s.ZLS to be arranged in a
variety of ways. The cookie can be trimmed to fit the
fixture. LightSticks can also be mounted to the back of
the light fixture if the metal area is sufficient to act as a
heat sink (12 square inches minimum).
Three ZLS LightSticks, using 7.2 watts, can be mounted
in a Surface Mount RV Scare Light to exceed the light output
of the standard 37.5 watt 1295 bulb. Use up to six
ZLSs for even more light. Purchase additional ZLSs LightSticks
here.
|
|
2 ea ZL3s w/base for
Only $12.98
for base with
1
ea ZL3 LightStick
Add to Cart
ships
from
stock |
B15s.nZL3 : a white nexLED™
lamp made from one to six zipLED™
LightSticks
with a total of 3 to
18 HyBright.3 LED
chips plugged into a B15s.ZLX base.
|
n ZL3s |
LEDs |
amps* |
watts |
lumens |
|
6 |
54 |
0.42 |
5.26 |
360 |
|
5 |
45 |
0.35 |
4.38 |
300 |
|
4 |
36 |
0.28 |
3.50 |
240 |
|
3 |
27 |
0.21 |
2.63 |
180 |
|
2 |
18 |
0.14 |
1.75 |
120 |
|
1 |
9 |
0.07 |
0.88 |
60 |
*running at 12.5 volts, typical in off-grid rig
The double-stick
tape on the back of the LightSticks, and the optional mounting
plate, allows the B15s.nZL3 series to be arranged
in a variety of ways. The sticks can be mounted to the back of
the light fixture. They can be arranged side-by-side on the
mounting plate to provide a panel of light, or the
plate can be cut to fit into a chandelier, facing either
direction.
The B15s.6ZL3 is suitable
as a replacement for the 1295 incandescent bulb in scare
lights. If even more light is needed, the B15s.5ZL3 can be expanded using
a ZLX.nZL3: a ZLX Extender and additional
ZL3 LightSticks.
The B15s.4ZL3 is a good
replacement for the 1156 bulb where high intensity light is
needed. The medium intensity B15s.3ZL3 can replace 1156 or
1141 in ceiling, patio, or task fixtures.
The B15s.2ZL3 is a good replacement
for the 1141 in general lighting applications, and the B15s.1ZL3 works very well as a
night-light or map-light.
1
to 6 zipLED™
LightSticks
3 HyBright.3 LED chips per
LightStick
9 to 54 LEDs, natural white specturm
60 to 360 lumens (at 12.5 volts)
wide-angle
perpendicular
to the base
B15s.ZLX socket
BA15s
base
(bayonet, 15mm)
10 mil aluminum
mounting plate (cookie)
12.5
volts nominal, regulated
10 to 18
volt operating range
0.07 to 0.42
amps nominal
0.88
to 5.26 watts
100,000 hour
lifetime
Purchase zipLEDs in Bulk
here.
|
Add to Cart
ships
from
stock |
B15.RV3-V : a white nexLED™ spotlamp suitable as a
replacement for 1138 and 1383 incandescent bulbs and for 1003,
1141, and 1156 incandescents in "bullet" fixtures used in RVs
and boats. Use where a more directed light is needed for close
work and reading.
9
HyBright-3 LED
chips on flat board
27 LEDs, CW
BA15s
base (bayonet, 15mm)
regular or
long-neck available
180 lumens
unidirectional
150 degree illumination
vertical
to the base
12.5 volts nominal
11 to
13.8 volt operating range
0.21 amps
nominal
2.63 watts
100,000 hour lifetime
|
LED Replacements for
15mm Bayonet Double Contact (BA15d) Bulbs
<>
|
ZLS w/base and metal cookie
for
Add to Cart
ships
from
stock |
B15d.ZLS : the brightest nexLED™
lamp made to date provides 220 lumens from a single LED
LightStick with two white Starion LED chips and a power
regulation circuit. Plugged into a B15d.ZLX base, one ZLS
provides 3.5 times the brightness of a ZL3,
exceeding the brilliance of an 1004 bulb.
2
each Starion(tm) LED chips
on a flat pcb
0.5 by
1.5 inches printed circuit board
double-stick
thermal tape backing
18 LEDs
per chip, 36 total
220 lumens,
natural white color
wide-angle
perpendicular
to the board
Color Rendering Index
of 92
Color Temperature of
3500 ~ 4500K
Power regulation
controls internal voltage
12.5 volts nominal internal voltage
10
to 30 volt operating range
2.4
watts, 0.2 amps at 12v
0.1 amps at 24v
Use with
pulse-width-modulation dimmers
Variable
voltage dimmers don't work
Operating
temperature 130F
LightStick
must be thermally attached to
12 sq-in of metal for proper operation
Will not melt
plastic lens cover
B15d.ZLX
double-contact socket
BA15d
base
(bayonet, 15mm)
10 mil aluminum
mounting plate (cookie)
3.4 x 3.4
inches, routing holes for wiring
100,000 hour lifetime
The
double-stick tape on the back of the LightStick, and the
mounting plate (cookie), allows the B15d.ZLS to be arranged in a
variety of ways. The cookie can be trimmed to fit the
fixture. LightSticks can also be mounted to the back of
the light fixture if the metal area is sufficient to act as a
heat sink (12 square inches minimum).
2
each Starion(tm) LED chips
on a flat pcb
0.5 by
1.5 inches printed circuit board
double-stick
thermal tape backing
18 LEDs
per chip, 36 total
220 lumens,
natural white color
wide-angle
perpendicular
to the board
Color Rendering Index
of 92
Color Temperature of
3500 ~ 4500K
Power regulation
controls internal voltage
12.5 volts nominal internal voltage
10
to 30 volt operating range
2.4
watts, 0.2 amps at 12v
0.1 amps at 24v
Use with
pulse-width-modulation dimmers
Variable
voltage dimmers don't work
Operating
temperature 130F
LightStick
must be thermally attached to
12 sq-in of metal for proper operation
Will not melt
plastic lens cover
B15d.ZLX
double-contact socket
BA15d
base
(bayonet, 15mm)
10 mil aluminum
mounting plate (cookie)
3.4 x 3.4
inches, routing holes for wiring
100,000 hour lifetime
The
double-stick tape on the back of the LightStick, and the
mounting plate (cookie), allows the B15d.ZLS to be arranged in a
variety of ways. The cookie can be trimmed to fit the
fixture. LightSticks can also be mounted to the back of
the light fixture if the metal area is sufficient to act as a
heat sink (12 square inches minimum).
|
|
2 ea ZL3s w/base for
Only $12.98
for base with
1
ea ZL3 LightStick
Add to Cart
ships
from
stock |
B15d.nZL3 : a white nexLED™
lamp made from one to six zipLED™
LightSticks
with a total of 3 to
18 HyBright.3 LED
chips plugged into a double contact B15d.ZLX base.
|
n ZL3s |
LEDs |
amps* |
watts |
lumens |
|
6 |
54 |
0.42 |
5.26 |
360 |
|
5 |
45 |
0.35 |
4.38 |
300 |
|
4 |
36 |
0.28 |
3.50 |
240 |
|
3 |
27 |
0.21 |
2.63 |
180 |
|
2 |
18 |
0.14 |
1.75 |
120 |
|
1 |
9 |
0.07 |
0.88 |
60 |
*running at 12.5 volts, typical in off-grid rig
The BA15d socket
is normally found in marine applications and a few RV
appliances. Plugging a BA15s bulb into a BA15d will normally
blow the fuse in the rig.
The double-stick tape on the back of the
LightSticks, and the optional mounting plate, allows the
B15d.nZL3 series to be
arranged in a variety of ways. The sticks can be mounted to
the back of the light fixture. They can be arranged
side-by-side on the mounting plate to provide a panel of
light, or the plate can be cut to fit into a chandelier,
facing either direction.
The B15d.6ZL3 is even
brighter than the 1076 incandescent bulb. If even more light
is needed, the B15d.5ZL3
can be expanded using a ZLX.nZL3: a ZLX Extender and additional
ZL3 LightSticks.
The B15d.4ZL3 is a good
replacement for the 1142 bulb where high intensity light is
needed. The medium intensity B15d.3ZL3 can replace 1004 or
1142 in ceiling, patio, or task fixtures.
The B15d.2ZL3 is a good replacement
for the 1142 in general lighting applications, and the B15d.ZL3 works very well as a
night-light or map-light.
1
to 6
zipLED™
LightSticks
3 HyBright.3 LED chips per
LightStick
9 to 54 LEDs, natural white specturm
60 to 360 lumens (at 12.5 volts)
wide-angle
perpendicular
to the base
B15s.ZLX socket
BA15s
base
(bayonet, 15mm)
10 mil aluminum
mounting plate (cookie)
12.5
volts nominal, regulated
10 to 18
volt operating range
0.07 to 0.42
amps nominal
0.88
to 5.26 watts
100,000 hour
lifetime
Purchase zipLEDs in Bulk
here. |
|
Go to Top -- View Your Cart / Checkout
nexLED™ Replacements
for
Wedge Bulbs With a 9.5x2.1mm Base
If your incandescent bulbs look like
the bulb below, you have bulbs with the Wedge base. Wedge bulbs were developed as a
cost-reduced solution for interior lighting applications.
Typical bulb numbers are 906, 912, and 921.
These are commonly used in some decorative scones and chandiler
lighting and in ceiling fixtures and basement and patio lights. They
are also found in stove hood lighting.
|
The W9-series 9.5 mm wedge-base miniature
incandescent bulb numbers are 922, 921, 912, 906 and 194. The
base is all glass, nominally measuring 9.5mm by 2.1mm. The
bulb measures 15mm in diameter and is nominally 1.5 inches
long.
NOTE: we have found that some socket
manufacturers have built to the lower limit of the 9.5 x 2.1mm
standard. If your LightBlasters replacement does not fit the
socket, file down the edge of the connection paddle and/or
shave down the solder on the contacts to fit the socket
without undue force. |
There is also
a series of sub-miniature wedge bulbs that are only 10mm in diameter
and an inch long. While the W9 LED lamps might fit their socket, the
lamp may be too large to fit the lighting fixture. LightBlasters
does not yet make a replacement for the sub-miniature wedge bulb.
|
|
Add to Cart
ships
from
stock |
W9.RV2N-H : a CR90 warm white
nexLED™ HyBright.3 LED lamp
specifically designed for use wedge bulb fixtures found in the
ceilings and over the counters of many motor coaches and other
RVs. These LEDs are the latest development in the HyBright
technology and provide good excellent color rendering at 3800K
color temperature.
6 HyBright.3 LED
chips on a flat board
18 LEDs, WW (3800K)
9.5mm base for W9 socket
120 lumens
wide-angle
perpendicular
to the board
12.5 volts nominal
11
to 18 volt operating range
Power-limiting circuit protects LEDs
0.14 amps nominal
1.75 watts
100,000 hour lifetime
This
lamp replaces the typical 906 or 912 bulb found in many
fixtures in motorcoaches and trailers. The lamp's 120 lumens
is about the same as seen in the ceiling fixtures since
none of its luminosity is lost to the reflector.
This lamp is a great replacement in most
ceiling fixture applications. The CR90 color rendering of the LEDs is
in the warm range, and applications requiring accurate color
rendering, such as oil painting are well served.
|
The
W9.RV3N-H
is temporarily
OUT-OF-STOCK
Our supplier changed his specifications
for the LED chip, producing an inferior product.
We are looking
for a new supplier.
We apologize for this short notice -- we
were as surprised as you. |
W9.RV3N-H : a 200 lumen CR90
warm white nexLED™ HyBright.3 LED lamp
specifically designed for use in ceiling and sconce fixtures
using 921 bulbs.
These LEDs are the latest development in
the HyBright technology and provide good excellent color
rendering at 3800K color temperature.
10 HyBright.3 LED
chips on a flat board
30 LEDs, WW, CR90
wedge base
200
lumens
wide-angle
perpendicular
to the board
12.5 volts nominal
11
to 18 volt operating range
Power-limiting circuit protects LEDs
0.24 amps nominal
2.9 watts
100,000 hour lifetime
The CR90 color rendering of the LEDs is
in the warm range, and applications requiring accurate color
rendering, such as oil painting are well served.
|
|
ZLS w/base and metal cookie
for
Add to Cart
ships
from
stock |
W9.ZLS : the brightest nexLED™
lamp made to date provides 220 lumens from a single LED
LightStick with two white Starion LED chips and a power
regulation circuit. Plugged into a W9.ZLX base, one ZLS
provides 3.5 times the brightness of a ZL3,
exceeding the brilliance of an 921 bulb.
2
each Starion(tm) LED chips
on a flat pcb
0.5 by
1.5 inches printed circuit board
double-stick
thermal tape backing
18 LEDs
per chip, 36 total
220 lumens,
natural white color
wide-angle
perpendicular
to the board
Color Rendering Index
of 70
Color Temperature of
5300K
Power regulation controls
internal voltage
12.5 volts nominal internal voltage
10
to 30 volt operating range
2.4
watts, 0.2 amps at 12v
0.1 amps at 24v
Use with
pulse-width-modulation dimmers
Variable
voltage dimmers don't work
Operating
temperature 130F
LightStick
must be thermally
attached to
12 sq-in of metal for proper operation
Will not melt
plastic lens cover
921 socket
W2.1x9.5d
base
(9mm glass wedge)
10 mil aluminum
mounting plate (cookie)
3.4 x 3.4
inches, routing holes for wiring
100,000 hour lifetime
The
double-stick tape on the back of the LightStick, and the
mounting plate (cookie), allows the W9.ZLS to be arranged in a
variety of ways. The cookie can be trimmed to fit the
fixture. LightSticks can also be mounted to the back of
the light fixture if the metal area is sufficient to act as a
heat sink (12 square inches minimum).
2
each Starion(tm) LED chips
on a flat pcb
0.5 by
1.5 inches printed circuit board
double-stick
thermal tape backing
18 LEDs
per chip, 36 total
220 lumens,
natural white color
wide-angle
perpendicular
to the board
Color Rendering Index
of 70
Color Temperature of
5300K
Power regulation controls
internal voltage
12.5 volts nominal internal voltage
10
to 30 volt operating range
2.4
watts, 0.2 amps at 12v
0.1 amps at 24v
Use with
pulse-width-modulation dimmers
Variable
voltage dimmers don't work
Operating
temperature 130F
LightStick
must be thermally
attached to
12 sq-in of metal for proper operation
Will not melt
plastic lens cover
921 socket
W2.1x9.5d
base
(9mm glass wedge)
10 mil aluminum
mounting plate (cookie)
3.4 x 3.4
inches, routing holes for wiring
100,000 hour lifetime
The
double-stick tape on the back of the LightStick, and the
mounting plate (cookie), allows the W9.ZLS to be arranged in a
variety of ways. The cookie can be trimmed to fit the
fixture. LightSticks can also be mounted to the back of
the light fixture if the metal area is sufficient to act as a
heat sink (12 square inches minimum).
|
|
2 ea ZL3s w/base for
Only $12.98
for 1 ea ZL3 LightStick w/base
Add to Cart
ships
from
stock |
W9.nZL3 : a white nexLED™
lamp made from one to six zipLED™
LightSticks
with a total of 3 to
18 HyBright.3 LED
chips plugged into a W9.ZLX base.
|
n ZL3s |
LEDs |
amps* |
watts |
lumens |
|
6 |
54 |
0.42 |
5.26 |
360 |
|
5 |
45 |
0.35 |
4.38 |
300 |
|
4 |
36 |
0.28 |
3.50 |
240 |
|
3 |
27 |
0.21 |
2.63 |
180 |
|
2 |
18 |
0.14 |
1.75 |
120 |
|
1 |
9 |
0.07 |
0.88 |
60 |
*running at 12.5 volts, typical in off-grid rig
The double-stick
tape on the back of the LightSticks, and the optional mounting
plate, allows the W9.nZL3 series to be arranged in
a variety of ways. The sticks can be mounted to the back of
the light fixture. They can be arranged side-by-side on the
mounting plate to provide a panel of light, or the
plate can be cut to fit into a chandelier, facing either
direction.
The W9.6ZL3 is suitable
as a replacement for the two or three
921 incandescent bulb. If even more light is needed, the
W9.5ZL3 can be expanded
using a ZLX.nZL3: a
ZLX Extender and
additional ZL3
LightSticks.
The W9.4ZL3 is a good
replacement for a single 921 bulb where high intensity light
is needed. The medium intensity W9.3ZL3 can replace 921 or 912
in ceiling, patio, or task fixtures.
The W9.2ZL3 is a good replacement
for the 912 in general lighting applications, and the W9.ZL3 works very well as a
night-light or map-light.
1
to 6
zipLED™
LightSticks
3 HyBright.3 LED chips per
LightStick
9 to 54 LEDs, natural white specturm
60 to 360 lumens (at 12.5 volts)
wide-angle
perpendicular
to the base
B15s.ZLX socket
BA15s
base
(bayonet, 15mm)
10 mil aluminum
mounting plate (cookie)
12.5
volts nominal, regulated
10 to 18
volt operating range
0.07 to 0.42
amps nominal
0.88
to 5.26 watts
100,000 hour
lifetime
Purchase zipLEDs in Bulk
here. |
SOLD
OUT
use
W9.RV2N-H
W9.RV3N-H |
W9.RV3-H : a white nexLED™ HyBright-3 LED chip lamp
suitable as a replacement for 921 incandescents in RVs.
However, with a unidirectional format, it casts up to twice
the intensity of light as the 921. Use where full intensity
lighting is required, such as a primary light source in
ceiling fixtures, over-the-counter lighting, or as an outside
patio light.
9
HyBright-3 LED
chips on flat board
3 rows of
3 chips each
27 LEDs, CW
Wedge base (9.5 by 2.1mm)
180 lumens
unidirectional
150 degree illumination
vertical
to the base
12.5 volts nominal
11 to
13.8 volt operating range
0.21 amps
nominal
2.63 watts
100,000 hour lifetime
|
Remember, LED Lamps replace hot incandescent
and halogen bulbs used for RV and Boat interior lighting fixtures.
You save 80% in power and run cooler.
Go
Green with LEDs!
Go
Green with LEDs!
|
|
